fullarchive.blogg.se

Enter the vehicle’s VIN as the “File name” to make the file easy to find later. (ii) This opens the “Data Monitor” dialogue box.

(i)Select the “Save” button (circled) at the top left of the screen. The recorded file should now be saved so it is not accidently lost before it can be reviewed in detail. (ii) Once the recording has stopped, the graph of data is automatically displayed.ĭata can be viewed as required in either graphical or numerical form. Recording stops at 100%.ĭO NOT PRESS THE “Stop” BUTTON DURING THE RECORDING OR THE DATA WILL BE LOST. (i)Once prepared, touch “RECORD”on the bottom right of the screen to capture the activity of the engine as described above in step #6.Watch the recording time bar graph (circled at right). The recording activityis basically as follows (i) Touch record.(ii) Immediately start Engine & allow to idle for 2 seconds max.(iii) Race engine twice & allow to idle again until the end of recording.The above must be carried out as quickly as possible in order to maximise the recorded data on the graphs. (iii) Touch “Start” once the screen returns to the“Monitor Menu” screen. (ii) Select “Confirm” on the bottom right of the screen. Otherwise, the recording will start automatically as soon as a DTC is detected. (i) Select the second tab “Trigger Condition 1”.This provides access to trigger condition settings.Un-select the “DTC Trigger”box if the ECM has a permanent DTC in it. Move it to 20% Preand 80% Post (circled). (iv) Trigger Point:Adjust the “Trigger Point” (arrow at right). default.For this exercise, set the “Recording Time”to 20 seconds(arrow at right) so as not to make the graphs too large. (iii) Recording Time:There maybe cases where the recording time needs to be extended beyond the 10 sec. (ii) Sampling Rate:Slow down the “Sampling Rate” from every 10ms to every 20ms.This can be done by selecting the drop down icon. In some cases, the default settings may be all that are required.(i) Touch the “Setting”tab (circled right). (ii) Highlight the desired items from the list on the screen. (i) Clear the pre selected Main Signals items by touching “Clear Monitor Item”. Take careful notice of vehicles fitted with I-KEY.2.From the “Self Diagnostic Result” screen, select the “Data Monitor”tab. J31 Maxima (All variants 2009MY>)-250 ST-L variant is notfitted with “I-KEY”-250 ST-L / 350 ST-S variants are notfitted with “AV C/U” (colour screen / Sat Nav)ĬONFIGURATIONK13 Micra (All variants 2010 MY >) Z51 Murano(All variants 2009MY >)-2009MY ST Muranois notfitted with “I-KEY”-2010MY> ST Muranois fitted with “I-KEY”(Look for small button on the exterior door handles -both front doors to confirm) R51 Pathfinder / D40 Navara(Spain / Thai)-The list shown right applies to all R51 & Spain build D40-For all Thailand build D40, there is only 1 changeable item “KEYLESS ENTRY”-For all D40 RX 2005 ~ 2010MY, KEYLESS ENTRY = WITHOUT Refer to the list shown right for these settings. For earlier models, there are only 4 changeable items.

T31 X-TRAIL (All variants 2007MY>)-List shown right applies from July 2010 onwards. Otherwise the settings shown right apply to all J10 variants. For earlier models, PTC HEATER & DTRL does not appear on list. J10 Dualis(All variants 2008MY>)-List shown right applies from Oct 2009 onwards. (otherwise an Alarm will sound when A/T shift lever is in the “R” position. The configuration of most current models is included on the following pages.Ĭ11 Tiida(All variants 2006MY >)-2010MY> Ti Hatch / Sedan variants with “AUTO A/C”.-Regardless of Transmission fitted, do not set “TRANSMISSION” as “A/T”. If there is any doubt on what to write to the BCM, connect CONSULT to another vehicle of the same specification & utilise the “Print Screen”option & print off each configuration screen. Click this “OK”button & then the new settings will be locked into place. To configure a BRAND NEW BCM to a vehicle (or change any settings) –select the “Manual Configuration” option.Īll settings need to be changed to suit the current vehicle.(i) Click on the drop-down arrows (circled) to make the correct settings for each BCM function.(ii) Once any settings have been changed, click the “Next” button in the RH bottom corner of the screen.Īn “OK” button will then appear in it‟s place. NOTE:Currently the BCM is configured Manually and the VIN is not required.(i) To progress to the next screen, simply enter any letter into the first VIN box.(ii) Select “Confirm”. The next screen asks for the VIN to be entered.